MBL-6010Dse OP- Pre- Amplifier DIY KIT & Finished Board

$15.2 Buy It Now or Best Offer
free,30-Day Returns

Seller Store laser-makers
(1211) 100.0%,

Location: wuhan
Ships to: US,
Item: 134850654982

Return shipping will be paid by:Buyer
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money Back
Zero:Zero
Type:Board
Unit Type:Unit
MPN:Does Not Apply
Country/Region of Manufacture:China
Unit Quantity:1
To Fit:—

MBL-6010Dse OP- Pre- Amplifier DIY KIT & Finished Board DIY KIT ProjectTo complete this project, high level knowledge of electronics and rich experience in terms of soldering and testing are required.Due to time zone and language communication restrictions, we can only provide limited technical support, and you need to solve problems by yourself.We do not provide information other than the product introduction page.MOFI MBL-6010Dse OP- Pre- Amplifier DIY KIT ProjectIt is based on the core circuit of the MBL 6010D Pre- Amplifier.Dual op amp design, can replace different op amps to present different sound performance.single-point grounding, ground resistance is close to the 0.02 ohm resistance value, low noisedesign.PCB is small and flexible, more suitable for all kinds of chassis installation. More cost-effective sound modification plan.Input Resistance: 47KGain: 5.5XPCB SIZE :77x70x1.6mm 1oz Cu, HASL with leadPower requirements: Best:[email protected] configurationDIY kit: Contains the PCB and the components needed on the PCB, but does not include the power transformer .Finished board: Based on the well-tested board on the standard version kit, we verified all key points’ voltage, and used the signal generator and oscilloscope for analog waveform double verification. We will not use this board for listening test.All finished pcbs are all carefully hand-soldered and fully tests, so the price is higher and less cost performance. Price-sensitive consumers but with have DIY ability are recommended to choose the kit.Schematic & key point of debuggingPCB comes with component parameters for easy installation.We only refer the schematic of the amplification part of the circuit. If you need full circuit parameter, please read the component value with the PCB by yourself; we do not provide additionally.please keep test point voltage close enough to it, +-20% is also permittedDIY KIT InstructionsSince the PCB holes are plated through, you only need to solder the parts from the bottom of the board. Do not drill or enlarge the holes because that would damage the through-plating.Clean both sides of the blank PCB with paper towel and isopropyl alcohol or electronics flux remover, then solder the components to the board, starting with the lowest profile parts.Make sure the correct part goes into each position on the circuit board. Measure each resistor with your multimeter to ensure it’s the proper value.Clean up the solder flux residue from the board with isopropyl alcohol (or electronics flux remover) and a brush.Inspect all solder connections carefully, using a magnifying glass, to make sure there are no solder bridges or cold solder joints. Use a multimeter in ohms scale to check for short circuits. As a minimum, you should verify that the V+ and V- DC inputs are not shorted to ground, or to each other, and that the output pad isn’t shorted to ground. Correct any mistakes before proceeding to the next phase.Parts listPayment Method: PayPal preferred Shippment:1. Shipping to international by China Post Airmail, every parcel will be registered with tracking number. We can also ship by FedEx/TNT/EMS for alternative shipping method for corresponding fees. Please let us know before payment if you need split shipment. 2.International shipping requires complicated shipping procedures (such as both countries customs, transit stations etc.), also will be affected by many factors, such as holidays, weather conditions etc, If you have not received your shipment within 30 days from payment, please contact us. Returns & Replacements & Repair:We accept returns & replacements within 30 days from the day the customer receive the products, please make first contact within 30 days from receiving the order. Products should be returned in original condition. As a benefit to our customers, we also provide repair within 3 months from the day when this item is shipped out, after repair is done, we will send you the item, but the customer should pay both shipping ways. Feedback:1)Your Feedback is really important to us, please take a few seconds to leave great feedback if you are satisfied with our product or service, thanks!2)We always offer the lowest price for best goods and service to you.3) Please contact us before leaving neutral(3 stars) or negative(1-2 stars) feedback.We will try our best to solve the problem and make you satisfied.

Frequently Asked Questions About MBL-6010Dse OP- Pre- Amplifier DIY KIT & Finished Board in My Website

123design.org is the best online shopping platform where you can buy MBL-6010Dse OP- Pre- Amplifier DIY KIT & Finished Board from renowned brand(s). 123design.org delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling MBL-6010Dse OP- Pre- Amplifier DIY KIT & Finished Board on 123design.org?

THƯ VIỆN KHỔNG LỒ

CẬP NHẬT TỨC THÌ

HOTLINE 24/7

Frequently Asked Questions About MBL-6010Dse OP- Pre- Amplifier DIY KIT & Finished Board in My Website

What are the best-selling MBL-6010Dse OP- Pre- Amplifier DIY KIT & Finished Board on 123design.org?

Trả lời Hủy

THƯ VIỆN KHỔNG LỒ

CẬP NHẬT TỨC THÌ

HOTLINE 24/7

Frequently Asked Questions About MBL-6010Dse OP- Pre- Amplifier DIY KIT & Finished Board in My Website

What are the best-selling MBL-6010Dse OP- Pre- Amplifier DIY KIT & Finished Board on 123design.org?

Trả lời Hủy

Đăng nhập