Electronic Ignition Conversion Kit for Lucas 35D8 Distributor 8-Cyl Rover, Rolls

$79.95 Buy It Now or Best Offer
free,30-Day Returns

Seller Store hot-spark
() %,

Location: Austin, Texas, United States
Ships to: US,
Item: 312585513186

Condition:New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is … Read moreabout the conditionNew: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller’s listing for full details. See all condition definitionsopens in a new window or tab
Interchange Part Number:LU-183, 3LUC8-35D
Other Part Number:3LUC8-35D
Part Brand:Hot-Spark
Manufacturer Part Number:3LUC8-35D-Rover-Rolls
Hot Spark:Hot Spark

eBay Electronic Ignition Conversion Kit for Lucas 8-cylinder 35D8 Distributors Electronic Ignition Conversion Kit Replaces Points and Condenser-Never Adjust Points or Timing Again! for Lucas 35D8 8-cylinder Distributors with single points (for 12-volt, negative ground electrical systems only) The Hot-Spark electronic ignition conversion kit replaces breaker points and condenser in the distributor to provide rock-solid reliability. With the Hot-Spark electronic ignition, dwell and timing are always spot-on accurate. centrifugal-advance -matter how strong your engine is, you won’t get the most out of it without a good spark. The stock Lucas ignition system used technology that dates back a century-to the Kettering system, which was introduced in the 1910 Cadillac. Even though you can adjust breaker points for near-electronic ignition performance, they will burn and wear within a few thousand miles, long before the recommended replacement interval. With points, the timing will drift; power and fuel economy will suffer. The Hot-Spark electronic ignition conversion kit delivers a strong spark every time and is maintenance-free. You’ll notice quicker starts, more top end power and a little gas mileage boost. It’s as easy to install as points and condenser! Advantages of the Hot-Spark electronic ignition conversion kit: Replaces points and condenser with solid-state electronics Set it and forget it – Never adjust points and timing again! Zero maintenance Delivers far more voltage to the spark plugs than points-based points Reliable Hall-effect technology Never gets out of adjustment Rock-steady reliability Dwell and timing are always spot-on accurate Increased gas mileage, fuel economy Quick starting Smooth idling Cleaner emissions Longer spark plug life Longer engine life Cleaner engine oil due to less unburned fuel Longer interval between oil changes Easy to install – If you can install points, you can install the Hot-Spark electronic ignition conversion No points to wear, burn, pit or corrode No condenser needed Absolutely no points float – zero – even at redline RPM and beyond! Never worry about drifting dwell or timing again No rubbing parts – nothing to wear out! Fits completely under the distributor cap Stealth modification – maintains stock appearance Includes everything you need, no external ignition box required. Works with stock distributor and coil Encased in high-temp thermoplastic – protected from the elements and oil, grease, dirt, water, etc. Never bother with points or condenser again! The best investment you’ll ever make for your vehicle Saves precious ($$$) fuel Coil with 1.5 Ohms or more internal, primary resistance required. Requires a 12-volt, negative ground electrical system. External Ballast Resistor: If the charging system voltage, measured at the coil’s + terminal, is more than 14.0 volts at any RPM level, the voltage regulator likely needs replacing or a 1.4 Ohm ballast resistor should be wired between the coil’s + terminal and the red HotSpark ignition wire. Too much voltage can damage the ignition module and other electronic components. How many miles until the Hot-Spark electronic ignition conversion kit pays for itself? Click here Measuring Coil Resistance (and more): www.Hot-Spark.com/Coil.htm The 3LUC8-35D ignition kit will replace only later-type points that leave a 5mm pivot pin standing upright from the breaker plate. This ignition kit will not replace earlier-type points. For Lucas Distributors: 8-cylinder Lucas (35D8 with single points) – 3LUC8-35D Aston Martin 1969-73 8-cyl DBS – Lucas 35D8 – 3LUC8-35D Bentley 1969-75 8-cyl T Series – Lucas 35D8 distributor, CCW, vacuum-advance – 3LUC8-35D 1973 8-cyl T Series – Lucas 35D8 distributor, Continental – 3LUC8-35D Land Rover 1970-85 V8 Engine, all models – Lucas 35D8 distributor, distributor (points-based), 8-cyl, CW, vacuum-advance – 3LUC8-35D Lucas Distributors 35D8 (Rolls-Royce, Triumph Stag) 8-cyl, CCW – 3LUC8-35D 35D8 (Rover, Morgan, MG, Range Rover) 8-cyl, CW – 3LUC8-35D MG MGB GT V8 1973-76 Lucas 35D8 distributor, distributor, 8-cyl, CW, vacuum-advance – 3LUC8-35D 1975-76 8-cyl MGB V8 – Lucas 35D8 distributor – 3LUC8-35D Morgan 1969-75 Plus 8 – Lucas 35D8 distributor, (points-based) 8 CW vacuum-advance – 3LUC8-35D 1970-74 8-cyl Plus Eight – Lucas 35D8 – 3LUC8-35D Range Rover 1969-84 all models – Lucas 35D8 distributor, (points-based) 8-cyl, CW, vacuum-advance – 3LUC8-35D Rolls-Royce 1969-76 Corniche, Silver Shadow – Lucas 35D8 distributor (points-based) 8-cyl, CCW, vacuum-advance – 3LUC8-35D 8-cylinder Lucas (35D8) – 3LUC8-35D LUCAS 35D8 distributors (with single points only): Note: If your 35D distributor has a Green and White lead: connect it to ground. All Rover V8 engines with 35D distributor Aston Martin: 1969-73 DBS V8 5.3 Bentley: 1972-75 T Serie Corniche Land Rover: 1967-73 3.0/3.5 101 Forward Control, 109 S3, 110 S4, Defender, Discovery, 1970-85 Range Rover 3.5, Serie III “Stage One” MG: 1972-76 B GT V8, RV8 Morgan: 1969-74 Plus 8 Rover: P5, P6, SD1 Sisu: NA-140 BT Rolls-Royce: 1969 – 77 Phantom VI, 1970 – 75 Silver Shadow, Corniche Triumph: 1970-77 TR7 V8 Rally, TR8 TVR: S-Serie, Chimaera, Griffith Westfield: Seight www.Hot-Spark.com/Installing-Hot-Spark-Lucas.pdf International Buyers – Please Note: Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility. Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying. VERY IMPORTANT — BEFORE ORDERING: Some distributors of vehicles, boats, etc. may differ, according to whether the stock distributor is still in place or a replacement distributor has been installed. Some otherwise similar or identical engines use different distributor brands and/or different distributor part numbers. We need your distributor’s brand name, distributor part number and number of engine cylinders to ensure that the electronic ignition conversion kit is correct one for your particular distributor. If your Lucas distributor part number, normally found on the side of the distributor body, is not among those listed on the relevant web page, chances are, the HotSpark ignition conversion kit won’t fit your distributor. It’s imperative that we know your distributor’s brand name, distributor part number and the number of cylinders of your engine. You may need to remove the distributor temporarily, so that you can read the distributor part number from the side of the distributor body. Usually, the side of your distributor will be covered with oil and dirt, so you’ll need to clean it to find the distributor brand name and exact part number. We can guarantee only that each of our ignition kits will fit a distributor with one of the distributor part numbers listed on its relevant web page. Otherwise, it likely won’t fit. HotSpark ignition kits require a 12-volt, negative ground (earth) electrical system. If you order the wrong electronic ignition conversion kit for your distributor, you’ll need to return it to us, via US Postal Service mail within 45 days from date of purchase. If the ignition kit is in perfect, unused condition, we can accept it as a retuned item, within 45 days of purchase, and provide a refund to your PayPal account, less a 20% restocking fee and any international shipping fees, etc., but only if the ignition kit is in pristine, unused condition. Buyer is responsible for shipping and other costs to return the product for credit or exchange. 3LUC8-35D Electronic Ignition Conversion Kit for 8-cylinder Lucas 35D8 Distributors with Points and Condenser Easy to Install – Replace Points and Condenser with Solid-State Electronics Hot-Spark Electronic Ignition Conversion Kit for 8-cylinder 35D8 Lucas Distributors with single points and condenser For Distributors: Lucas 8-cylinder 35D8 distributors with single points and condenser Application: 12V negative ground only. Coil Required: Coil must have 1.5 Ohms or more internal, primary resistance. In stock: Available: Item Number: 3LUC8-35D Price: US $79.95 FREE SHIPPING to anywhere in the USA Item Name: Hot-Spark Electronic Ignition Conversion Kit for 8-cylinder Lucas 35D8 Distributors with points/condenser Includes everything you need – no external ignition box required. Includes heavy-duty 35D red rotor. Price: US $79.95 Price with Shipping Shipped within USA $69.95 USD Shipped to Other Countries $109.95 USD HS14BR Hot-Spark 1.4 Ω Heavy-Duty Ceramic External Ballast Resistor 1.4 Ohm Ballast Resistor – Ideal for Use with Electronic Ignition and High-Voltage Charging Systems Also reduces burning and pitting of contact breaker points. 1.4 Ω heavy-duty, external ceramic ballast resistor – installed between coil’s + terminal and condenser or HotSpark ignition’s red wire. Lowers amperage to points or ignition module, ensuring trouble-free operation. Installed on engine firewall or on coil. Ideal for use with high-voltage charging systems and electronic ignition or points. Application: Recommended for use with high-voltage charging systems. Typically lowers current @ 3,000 RPM by about 0.5 amps. Supplements original stock coil. Also extends the life of points when used with points-based ignition systems. Reduces burning and pitting of points. In Stock: Available: Item Number: HS14BR Price: US $15.95 FREE SHIPPING to anywhere within the USA. Ships to USA only – no international shipping available for this item, unless ordered with distributor, coil or ignition kit. Charging system voltage, measured at the coil’s + terminal, must never exceed 13.9 volts, at any RPM level. You can reduce over-amperage surges/voltage spikes to the ignition module by wiring a 1.4 Ohm ballast resistor between the coil’s + terminal and the red Hot Spark ignition module’s red wire. Price with Shipping Shipped within USA $15.95 USD Dealer Inquiries welcomed. © 2005-2022 Hot Spark® LU-

Frequently Asked Questions About Electronic Ignition Conversion Kit for Lucas 35D8 Distributor 8-Cyl Rover, Rolls in My Website

123design.org is the best online shopping platform where you can buy Electronic Ignition Conversion Kit for Lucas 35D8 Distributor 8-Cyl Rover, Rolls from renowned brand(s). 123design.org delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling Electronic Ignition Conversion Kit for Lucas 35D8 Distributor 8-Cyl Rover, Rolls on 123design.org?

THƯ VIỆN KHỔNG LỒ

CẬP NHẬT TỨC THÌ

HOTLINE 24/7

Frequently Asked Questions About Electronic Ignition Conversion Kit for Lucas 35D8 Distributor 8-Cyl Rover, Rolls in My Website

What are the best-selling Electronic Ignition Conversion Kit for Lucas 35D8 Distributor 8-Cyl Rover, Rolls on 123design.org?

Trả lời Hủy

THƯ VIỆN KHỔNG LỒ

CẬP NHẬT TỨC THÌ

HOTLINE 24/7

Frequently Asked Questions About Electronic Ignition Conversion Kit for Lucas 35D8 Distributor 8-Cyl Rover, Rolls in My Website

What are the best-selling Electronic Ignition Conversion Kit for Lucas 35D8 Distributor 8-Cyl Rover, Rolls on 123design.org?

Trả lời Hủy

Đăng nhập